DIVERTRON
SUBMERSIBLE PUMPS

Divertron by DAB is a submersible electronic multi-impeller pump for clean water designed to increase water pressure, rainwater reuse, gardening and irrigation in residential building service.

Ideal for use in rain water systems and watering
networks, to pump water from cisterns, ponds, and wells, and for other applications requiring high pressure.

Multi-impeller submersible pump with integrated electronics for automatic switching on and off.

Dry run protection. Built-in non-return valve at the delivery

Submersible type continuous duty asynchronous motor. Thermal overheating protection. Wear-resistant motor shaft. 

Corrosion and oxidation resistant material. Stainless steel debris strainer.

Built-in
pressure switch, control circuit board and sensor.

Construction Industry

Wholesale & Retail Trade

Service Industry

Accommodation & 
Food Service Industry

DIVERTRON
Series

Divertron 650
Power
KW/HP 		Voltage
V 		Inlet
in. 		Flow Rate
L/min 		Head
M
0.42/0.56 230 1" 90 30

Dimensions

Cycle (Hz) A H H1 H2 H3 N.W. (kg)
50/60 160 488 469 455 548 9.5

Maximum immersion depth: 12 m
Type of pumped liquid: Clean, free from solid or abrasive substances, non-viscous, non-aggressive, non-crystallized and chemically neutral
Liquid temperature range: From 0°C to +40°C
Maximum immersion depth: 15 m
Flanges, thread: 1" (supplied as standard with a four-section fitting-reducer)
Pump maximum diameter: 160 mm
Impeller/s material: Technopolymer
Maximum number of starts: 20/h
Protection class: IP 68
Motor insulation class: F
Single phase power input: 230 V 50 Hz
Power cable (m) and plug: 15 m H07RNF with power plug
Possible type of installation: Fixed or movable in vertical position
Special versions on request: Cable of different light, different type of power plug

Brochure Manual Troubleshooting
Divertron 900
Power
KW/HP 		Voltage
V 		Inlet
in. 		Flow Rate
L/min 		Head
M
0.56/0.75 230 1" 97 44

Dimensions

Cycle (Hz) A H H1 H2 H3 N.W. (kg)
50/60 160 536 517 503 596 11

Maximum immersion depth: 12 m
Type of pumped liquid: Clean, free from solid or abrasive substances, non-viscous, non-aggressive, non-crystallized and chemically neutral
Liquid temperature range: From 0°C to +40°C
Maximum immersion depth: 15 m
Flanges, thread: 1" (supplied as standard with a four-section fitting-reducer)
Pump maximum diameter: 160 mm
Impeller/s material: Technopolymer
Maximum number of starts: 20/h
Protection class: IP 68
Motor insulation class: F
Single phase power input: 230 V 50 Hz
Power cable (m) and plug: 15 m H07RNF with power plug
Possible type of installation: Fixed or movable in vertical position
Special versions on request: Cable of different light, different type of power plug

Brochure Manual Troubleshooting

Frequently Asked Questions

W​What should I do to install the Divertron pump?

Pumps, including suction and booster pumps, run idle when there is little or no water. This leads to malfunctions ranging from wear and tear of chamber parts to burnout of the pump.

Unless it's an announced water cut, or you'd have to check constantly to see if there is enough water in your water tank–which could be quite inconvenient.

Pumps in Walrus' TS_B and HS_B series are all designed with low-water cut-offs. The design prolongs the life of the pumps and makes your life easier. Moreover, if you live in an old building or can't seem to find a solution to the water leaks in your home, try our TQC_B or HQC_B series, which are installed on rooftops for automatic flow control. The design prevents the building up of continual pressure in your water pipes and the pump won't be activated frequently by the leaks in your home.

What should I do to install the Divertron pump in a well?

Install the pump so that the pump suction is at least 1 m (3.28ft) above the bottom of the well to prevent the intake of sand and impurities. Use rigid metal pipes to hang the pump and secure the pipes with brackets at the top of the well.

For more information always check the pump manual, the updated version of the instruction manual is always available here on the website

What should I do to install the Divertron pump in a tank?

The minimum dimensions for the pump passage in the collecting tank must be greater than diameter 160 mm (6.7 in). Hold the pump slightly up from the bottom to avoid possible noises/vibrations transmitted to the tank. The pump will make noise if it is placed on the bottom of the tank. To avoid obstruction of the suction passages, it is recommended to check periodically that no dirt has accumulated in the collection trap (leaves, sand, etc.).For more information always check the pump manual, the updated version of the instruction manual is always available here on the website.

What should I do during the first start of the Divertron pump?

After connecting the pump to the mains, the pump motor is switched off and the non-return valve is at rest: if this is not the case, the pump stops, and the motor will never start

In the normal case, however, the pump behaves as follows:

  • If the hydraulic circuit upstream from the pump has a pressure higher than CUT-IN, the pump motor does not start, the priming is finished regularly.
  • If the circuit is not under pressure (P<CUT-IN), the pump motor is started. In this case,

o If the hydraulic circuit goes under pressure (P>CUT-IN) and there is no flow, for example because the delivery tap is closed, the motor is switched off 10 seconds after starting: the pump is primed.

o If there is no flow or pressure for 20 seconds (P

o Finally, if there is flow, the pump is primed and runs normally.

For more information always check the pump manual, the updated version of the instruction manual is always available here on the website.